Wilson Roof Pros provides professional flat & low-slope roofing in Wilson, NC for residential and commercial properties across the inner Coastal Plain between the Neuse and the Tar. Nearly every low-slope roof on a Wilson house is an addition. The older frame houses in town were extended with rear shed rooms as a matter of course, and post-war houses picked up dens, utility rooms and enclosed porches the same way. Each brought a shallow plane with it.
Those planes are where we spend most of our low-slope time, and the hard part is never the field. It is the point where the shed plane dies into the main roof. On a gabled house it lands against a wall and takes apron flashing. On a hipped house it lands into a sloping hip line, and there is no ridge, no wall and no square termination — just two planes meeting at an angle nobody designed.
That junction gets a self-adhered membrane carried well up both planes before anything else goes on, a metal transition formed to the actual angle rather than bent by eye, and the low-slope material lapped onto it in the right order. Done properly it disappears. Done with sealant it will leak inside three years and it will be blamed on the shingles above it.
Below three in twelve, asphalt shingles are the wrong product regardless of what the previous crew did. We use a self-adhered modified bitumen with a granulated cap sheet on small residential planes, which handles the shallow pitch and the foot traffic that a rear addition inevitably gets. On larger areas a single-ply membrane is the better answer. That is a product decision rather than a preference.
Drainage is the other half. A shallow addition roof on a flat lot has very little slope to work with, so we check for the ponding that leaves a tide line and we build up tapered sleepers to give it fall where the framing cannot. Standing water is not automatically a failure, but water still sitting there two days after rain is.
If your addition roof is shingled at two in twelve and has not leaked yet, we will tell you it is living on borrowed time rather than pretending it is fine, and we will also tell you it can usually wait for the main roof rather than being an emergency on its own. Bundling the two into one visit saves a mobilization, and we will price it that way when the timing works.
Our licensed and insured team brings the right materials and equipment to every job — hip-and-ridge cap counted as hip footage plus ridge footage, off-ridge box vents set two courses down from the peak, net free ventilating area figured against measured attic floor area, a pyramidal roof with no ridge line to cut, site-formed hip caps bent to the roof's own angle, closed-cut valleys where a rear shed ell dies into a hipped plane — and backs the work with a written workmanship warranty. We serve Wilson and nearby communities including Elm City, Black Creek, Lucama, Stantonsburg.
What We Handle
Everything our flat & low-slope roofing in Wilson covers
One crew, one point of contact, and the full range of flat & low-slope roofing work in Wilson, NC. If it is on this list we do it in house rather than handing it to a subcontractor:
- flat roof Wilson NC
- low slope roofing Wilson
- TPO roof Wilson NC
- modified bitumen roof Wilson
- flat roof repair Wilson NC
- rear addition roof Wilson
- porch roof repair Wilson NC
- low slope shingle Wilson
- EPDM roof Wilson NC
- flat roof replacement Wilson County
- shed roof addition Wilson NC
- ponding water roof Wilson NC
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Wilson services.
Materials, equipment and how we do flat & low-slope roofing
The difference between flat & low-slope roofing that lasts and flat & low-slope roofing that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with hip-and-ridge cap counted as hip footage plus ridge footage, off-ridge box vents set two courses down from the peak, net free ventilating area figured against measured attic floor area, a pyramidal roof with no ridge line to cut, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Wilson job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in the inner Coastal Plain between the Neuse and the Tar means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do flat & low-slope roofing outside Wilson
Wilson Roof Pros covers Wilson and the surrounding communities of the inner Coastal Plain between the Neuse and the Tar. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Flat & Low-Slope Roofing in Elm City, NC — Wilson County, population 1,218
- Flat & Low-Slope Roofing in Black Creek, NC — Wilson County, population 692
- Flat & Low-Slope Roofing in Lucama, NC — Wilson County, population 1,036
- Flat & Low-Slope Roofing in Stantonsburg, NC — Wilson County, population 762
- Flat & Low-Slope Roofing in Saratoga, NC — Wilson County, population 353
- Flat & Low-Slope Roofing in Sims, NC — Wilson County, population 275
Start on the Wilson Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Wilson Chooses Wilson Roof Pros
- ✓We record linear feet of ridge and linear feet of hip on every estimate, because cap footage and vent capacity both come from those numbers and a square count tells you neither.
- ✓We refuse ridge vents on roofs that cannot supply them. If the ridge is too short to carry the exhaust an attic needs, we fit off-ridge or hip vents and explain the arithmetic instead.
- ✓We repair sound old metal roofs rather than removing them. Fasteners, seams, rust conversion and a coating system beat a tear-off on most of the older frame houses around here.
- ✓We quote the plane when a plane is what failed. Hipped roofs are bounded by hips, so replacing one slope is straightforward and we would rather do that than sell a whole roof.
The standards behind flat & low-slope roofing
Quality here is not a matter of opinion — it is written down. The flat & low-slope roofing work we do in Wilson follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every flat & low-slope roofing project in Wilson gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free flat & low-slope roofing free estimate in Wilson, or request a quote and we'll get right back to you.